Amana Tool PR1040C Electro-Blu Carbide Tipped Prestige 10 Inch D 40T ATB 18 Deg 5/8 Bore Non-Stick Coated Circular Saw Blade from other stores
-
Amana Tool 610600C Electro-Blu...
Cut-Off & Crosscut Saw Blades Carbide tipped ATB (Alternate Top Bevel) General...
Cut-Off & Crosscut Saw Blades Carbide tipped ATB (Alternate Top Bevel) General cut-off & trimming of soft/hardwoods plywood wood veneer (top) No. 5 These blades are designed for smooth crosscuts in a variety of materials from hardwoods softwoods and...
more
-
-
Amana Tool - 610800C Electro-B...
Amana 610800C 10 /80T TRIM SAW A.T.B. GRIND For use on table saws sliding tabl...
Amana 610800C 10 /80T TRIM SAW A.T.B. GRIND For use on table saws sliding table saws miter saws radial arm saws leaving a super smooth finish in hardwood and softwoods. Great for trimming and sizing veneers and laminates. 10 Inch x 80 Teeth...
more
-
Amana Tool RB1020C Electro-Blu...
Carbide Tipped Designed for ripping hardwood and softwood this exceptional bla...
Carbide Tipped Designed for ripping hardwood and softwood this exceptional blade cuts fast and smooth. The flat top grind and the high positive hook angle reduce feed effort. The anti-kickback limits the thickness of chip; taken to offer a safer...
more
-
Amana Tool 651030-1 Carbide Ti...
Dadoes (cross-grain cuts) and grooves (cuts with the grain) are Cut efficientl...
Dadoes (cross-grain cuts) and grooves (cuts with the grain) are Cut efficiently on the table saw with a dado stack set. Unlike a wobbler a stack set produces a flat-bottom cut with chip-free edges. Amana Tool makes dado stack sets For every machine...
more
-
Amana Tool 610240C Electro-Blu...
Amana Tool 610240C Electro-Blu Carbide Tipped Ripping Standard 10 Inch D x 24T...
Amana Tool 610240C Electro-Blu Carbide Tipped Ripping Standard 10 Inch D x 24T FT 20 Deg 5/8 Bore Non-Stick Coated Circular Saw Blade Ripping Standard Saw Blades • Carbide Tipped • 5/8 Bore Brand: Amana Tool MPN: …
more
-
Amana Tool 610301C Electro-Blu...
Rip then glue up. With this exceptional blade there is no need for sanding or ...
Rip then glue up. With this exceptional blade there is no need for sanding or jointing after the cut. The precision Triple Chip grind and extra high hook angle allow aggressive feed rates yet produce an extra smooth cut finish. The thick plate...
more
-
Amana Tool 510801C Electro Blu...
Carbide tipped saw blades for cutting relatively thick-walled aluminum Aluminu...
Carbide tipped saw blades for cutting relatively thick-walled aluminum Aluminum Composite Material (ACM) and non-ferrous metal bars. The negative hook angle triple-chip grind and thick plate combine to produce a superior finish Cut extrusions and...
more
-
Amana Tool LB10801C Electro-Bl...
2 Negative Hook Modified Triple Chip (MTC) GrindWhen cutting acrylics such as ...
2 Negative Hook Modified Triple Chip (MTC) GrindWhen cutting acrylics such as Plexiglas polycarbonates such as Lexan and other plastics chip-weldinga melting of the materialis a concern. But not with these carbide tipped no melt saw blades. The...
more
-
Amana Tool 610721C Electro-Blu...
Carbide Tipped These blade are designed for cutting plastic laminate Plexiglas...
Carbide Tipped These blade are designed for cutting plastic laminate Plexiglas and solid surface materials such as Dupont Corian Wilsonart Gibraltor & Fountainhead. The Triple Chip grind is especially configured to leave a swirl free cut in solid...
more
-
-
Amana Tool 610800 Carbide Tipp...
Suitable for use on table saws sliding table saws radial arm saws and miter sa...
Suitable for use on table saws sliding table saws radial arm saws and miter saws of all types. Leaves a super smooth finish when cutting hard or softwood. It is especially suited to trimming and sizing veneers and laminates in single sheets or in...
more
-
Amana Tool TB10800 Carbide Tip...
Thin kerf blades are designed for miter smooth cuts; less drag on bearings and...
Thin kerf blades are designed for miter smooth cuts; less drag on bearings and brake and reduces stock loss on expensive woods and veneer plywoods. Not recommended to cut stock over 3/4 without the use of a stablizer. Carbide-Tipped. Safety...
more
-
Items per page