1-80
of
16,161
results
-
Amana Tool 45796 Finger Joint ...Amana Tool 45796 Finger Joint 2-Flute Carbide Tipped Router Bit 1/2-Inch Shank Amana Tool 45796 Finger Joint 2-Flute Carbide Tipped Router Bit 1/2-Inch Shank more
-
Amana Tool - 610600C Electro-B...As our standard Cut-Off and crosscut blade This is ideal for table saws and sl... As our standard Cut-Off and crosscut blade This is ideal for table saws and sliding Table saws. Its combination of 10° hook and the alternate top bevel tooth grind provide good-quality cuts and a long cutting life.Suitable for hardwood softwood even... more
-
Amana Tool 55242 Carbide Tippe...Carbide-Tipped 82 Degree Countersink with No Burning and Marring Adjustable Fr... Carbide-Tipped 82 Degree Countersink with No Burning and Marring Adjustable Free Spinning Low Friction Depth-Stop with No-Thrust Ball Bearing more
-
Amana Tool 56123 Carbide Tippe...Industrial Quality Signmaking Lettering V Groove Miter Fold & Mini Router Bits... Industrial Quality Signmaking Lettering V Groove Miter Fold & Mini Router Bits are made by Amana Tool the leading manufacturers of high-quality wood-cutting tools. Use Amana Tool 56123 Carbide Tipped Point Cutting Roundover 1/4 R x 1/2 D x 1/2 CH x 1/4... more
-
Amana Tool - 51310 Carbide Tip...Two cutting edges spaced 180 degrees apart each half the length of its flute. ... Two cutting edges spaced 180 degrees apart each half the length of its flute. One extends from the tip to the middle of the flute The other from the middle to end. The configuration combines the cutting speed and chip clearance of a single-flute bit... more
-
Amana Tool - 55462 Carbide Tip...These one piece stile & rail bits are an easy and effective technique for crea... These one piece stile & rail bits are an easy and effective technique for creating cabinet door frames. You simply adjust the height of the bit accordingly in the router Table to cut the profile Cut (with bit lowered in the table) and the cope cut... more
-
Amana Tool 510601 Carbide Tipp...The ideal carbide tipped saw blades for cutting relatively thick-walled alumin... The ideal carbide tipped saw blades for cutting relatively thick-walled aluminum and non-ferrous metal bars. The negative hook angle triple-chip grind and thick plate combine to produce a superior finish Cut extrusions and profilesExcellent for... more
-
Amana Tool - 45236 Carbide Tip...Diameter (D) 1 Cutting height (B) 3/4 Shank (D) 1/4 Overall length (L) 2 Flute... Diameter (D) 1 Cutting height (B) 3/4 Shank (D) 1/4 Overall length (L) 2 Flutes 2 more
-
Amana Tool 55331 Carbide Tippe...A must have tool for every woodworker Tool designed with a unique shank with h... A must have tool for every woodworker Tool designed with a unique shank with hex part and round part. Open space to allows for chip evacuation Adjustable heavy-duty revolving depth-stop HSS drill bit included Industrial quality carbide-tipped Quick... more
-
Amana Tool 45912 Carbide Tippe...Core Box Router Bits Cut half-round grooves for fluted moldings columns millwo... Core Box Router Bits Cut half-round grooves for fluted moldings columns millwork and signs using a core box bit. Used with an edge guide it can cut coves. Perfect for making flutes on CNC machines.Perfect for juice groove in cutting boards.Carbide... more
-
Amana Tool - 45806 Carbide Tip...The 14° dovetail Bit is used with common half-blind Dovetail jigs as well as ... The 14° dovetail Bit is used with common half-blind Dovetail jigs as well as with omnijig Incra and Leigh jigs. #45806 diameter (D) 1/2 angle (a°) 14° cutting height (B) 0.532 shank (D) 1/2 overall length (L) 2-1/2 Type Incra/omnijig 43750 flutes 2... more
-
Amana Tool 47108 Flush Trim wi...Amana Tool 47108 Flush Trim with Ball Bearing Guide 1/2-Inch Diameter by 1-Inc... Amana Tool 47108 Flush Trim with Ball Bearing Guide 1/2-Inch Diameter by 1-Inch more
-
Amana Tool 55390 Carbide Tippe...The lock Miter is an interlocking edge-to-edge joint typically used at the cor... The lock Miter is an interlocking edge-to-edge joint typically used at the corners of casework. Used in a table-mounted router run at reduced speed this bit cuts both halves of the joint. The same setup of bit and fence cuts both parts. One part is... more
-
Amana Tool - 47140 Carbide Tip...Use the flush trim router bit with bearing for laminate work or for template a... Use the flush trim router bit with bearing for laminate work or for template and pattern work. The miniature flush trim router bite are ideal to trim and shape small details in tight corners. more
-
Amana Tool 55239 Carbide Tippe...Carbide-Tipped 82 Degree Countersink with Adjustable Depth-Stop Carbide-Tipped 82 Degree Countersink with Adjustable Depth-Stop more
-
Amana Tool - 45705 Carbide Tip...Diameter (D) 1/2 Angle (a°) 60° Cutting height (B) 5/8 Shank (D) 1/4 Overall... Diameter (D) 1/2 Angle (a°) 60° Cutting height (B) 5/8 Shank (D) 1/4 Overall length (L) 1-3/4 more
-
Amana Tool 47154 Carbide Tippe...Trimming Router Bits are made by Amana Tool the leading manufacturers of high ... Trimming Router Bits are made by Amana Tool the leading manufacturers of high quality wood cutting tools. Eliminate the time-consuming hand-filing that normally follows each trimming cut on a laminate job with Amana Tool 47154 Carbide Tipped No-File... more
-
Amana Tool 45448 Carbide Tippe...Use a Two-Flute bit where fine finish is paramount. Two flutes balance the bit... Use a Two-Flute bit where fine finish is paramount. Two flutes balance the bit eliminating vibration that degrades the cut finish. Two cuts per revolution Yield a smooth surface but feed rate is slightly reduced #45448 diameter (D): 1 cutting height... more
-
Amana Tool - 49700 Carbide Tip...This bit creates a flat-bottom Groove between two quarter-round shapes. Short ... This bit creates a flat-bottom Groove between two quarter-round shapes. Short vertical walls extending below the radius lend extra depth to the appearance. Depending upon the cut depth adjustment The radii can be flush with the work surface or... more
-
Amana Tool - 54306 Carbide Tip...This bit produces a fingernail flute rather than a full 180° radius flute. Cr... This bit produces a fingernail flute rather than a full 180° radius flute. Creates an interesting edge detail and can be used to make small-scale cornice-type moldings. Use in a handheld or a table-mounted router #54306 diameter (D) 7/8 radius (r) 3/4... more
-
Amana Tool 45780 Carving and E...Amana Tool 45780 Carving and Engraving 2-Flute Carbide Tipped Router Bit 1/4-I... Amana Tool 45780 Carving and Engraving 2-Flute Carbide Tipped Router Bit 1/4-Inch Shank For fine-line engraving in wood and composite Materials Use either of these compact bits. Two-flute configuration and modest length (which minimizes vibration)... more
-
Amana Tool 49492 Carbide Tippe...Corner Rounding Router Bits with Ball Bearing Guide Corner Rounding Router Bits with Ball Bearing Guide more
-
Amana Tool - 45460 Carbide Tip...This bit is essentially a plunge-cutting straight with a shank-mounted ball-be... This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile useful for template/pattern routing of parts joints internal cuts and can be used in handheld and table-mounted routers. The template is attached to... more
-
Amana Tool - 45422 .. Carbide ...Amana Tool - 45422 .. Carbide Tipped Straight Plunge .. 1/2 Dia x 1-1/2 .. x 1... Amana Tool - 45422 .. Carbide Tipped Straight Plunge .. 1/2 Dia x 1-1/2 .. x 1/2 Shank more
-
Amana Tool 47126 Flush Trim Ex...Product Description Use this bit for template or pattern work where the workpi... Product Description Use this bit for template or pattern work where the workpiece is unusually thick. The Two-Flute configuration cuts fast and produces a smooth finish. For a superior finish Use the three-flute version. Twin bearings on selected tools... more
-
Amana Tool 1-1/4 Diam 1/2 LOC ...Amana Tool 1-1/4 Diam 1/2 LOC 2 Flute Carbide-Tipped Edge Profile Chamfer Rout... Amana Tool 1-1/4 Diam 1/2 LOC 2 Flute Carbide-Tipped Edge Profile Chamfer Router Bit 1/4 Shank Diam 2 OAL Use on Wood more
-
Amana Tool 45465 Flush Trim/Pa...3/4Inch Cutting Diameter 13/4Inch Cutting Height 33/4Inch Length 1/2Inch Shank... 3/4Inch Cutting Diameter 13/4Inch Cutting Height 33/4Inch Length 1/2Inch Shank 2 Flute Carbide Tipped Industrial Quality more
-
Amana Tool - (47090) Carbide T...Trimming Router Bits are made by Amana Tool the leading manufacturers of high ... Trimming Router Bits are made by Amana Tool the leading manufacturers of high quality wood cutting tools. Use Amana Tool 47090 Carbide Tipped Flush Trim 1/4 D x 1/2 CH x 1/4 Inch SHK x 2-1/4 Inch Long Router Bit w/ Lower Ball Bearing for laminate work... more
-
Amana Tool 45795 V-Groove 108 ...Industrial Quality Signmaking Lettering V Groove Miter Fold are made by Amana ... Industrial Quality Signmaking Lettering V Groove Miter Fold are made by Amana Tool the leading manufacturers of high-quality wood-cutting tools. Amana Tool 45795 V-Groove 108 Deg. Folding for Aluminum Composite Material (ACM) Panels Like Alucobond... more
-
Amana Tool - 45678 Carbide Tip...These bits are designed for slotting wood flooring inlays and medallions #4567... These bits are designed for slotting wood flooring inlays and medallions #45678 diameter (D) 1-1/4 Radius (r) 1/8 cutting Height (B) 1/4 shank 1/4 D) 1/4 overall length (L) 1-7/8 type Rounded replacement collar 7724 replacement bearing 47712 flutes 2 C... more
-
Amana Tool - 49408 Carbide Tip...Chamfer or bevel edges for decorative effect or to form edge Miter joints. Pro... Chamfer or bevel edges for decorative effect or to form edge Miter joints. Produce crisp uniform edges at accurate angles to make 4- 6- 8- 12- or 16-sided boxes. For best results use in a router table. #49408 diameter (D) 7/8 angle (a°) 15° cutting... more
-
Amana Tool - 620120 Carbide Ti...As our standard cut-off and crosscut blade this is ideal for table saws and sl... As our standard cut-off and crosscut blade this is ideal for table saws and sliding table saws. Its combination of 10° hook and the alternate top bevel tooth grind provide good-quality cuts and a long cutting life.Suitable for hardwood softwood even... more
-
Amana Tool 610300 Carbide Tipp...This is an excellent and popular general purpose configuration blade. Its low ... This is an excellent and popular general purpose configuration blade. Its low tooth count high hook angle and ample gullets make it an aggressive fast-cutting ripping blade. But its ATB grind allows it to crosscut well. A good choice for all-around... more
-
Amana Tool - 45226 Carbide Tip...Amana Tool - 45226 Carbide Tipped Straight Plunge High Production 1/2 Dia x 1 ... Amana Tool - 45226 Carbide Tipped Straight Plunge High Production 1/2 Dia x 1 4 S more
-
Amana Tool - 47114 Carbide Tip...For an extremely smooth finish Choose the three-flute configuration. It is esp... For an extremely smooth finish Choose the three-flute configuration. It is especially good to use on laminates that tend to chip Easily. #47114 diameter (D) 1/2 cutting height (B) 1 shank (D) 1/4 overall length (L) 2-5/8 replacement bearing 47706... more
-
Amana Tool 45366 Carbide Tippe...Trimming Router Bits are made by Amana Tool the leading manufacturers of high ... Trimming Router Bits are made by Amana Tool the leading manufacturers of high quality wood cutting tools. Amana Tool 45463-3TS Carbide Tipped Flush Trim Plunge Template 3/4 D x 1 CH x 1/2 Inch SHK w/ Upper Ball Bearing 3 Flute Router Bit is useful for... more
-
Amana Tool 610721C Electro-Blu...Carbide Tipped These blade are designed for cutting plastic laminate Plexiglas... Carbide Tipped These blade are designed for cutting plastic laminate Plexiglas and solid surface materials such as Dupont Corian Wilsonart Gibraltor & Fountainhead. The Triple Chip grind is especially configured to leave a swirl free cut in solid... more
-
Amana Tool - 47110 Carbide Tip...Diameter (D) 1/2 Cutting height (B) 1/2 Shank (D) 1/2 Overall length (L) 2-3/4... Diameter (D) 1/2 Cutting height (B) 1/2 Shank (D) 1/2 Overall length (L) 2-3/4 Replacement bearing 47706 more
-
Amana Tool 45422 Carbide Tippe...Straight Plunge Cutting Router Bits 1/2 Shank x 2 Flute - High Production Straight Plunge Cutting Router Bits 1/2 Shank x 2 Flute - High Production more
-
Amana Tool 55229 Carbide Tippe...Carbide-Tipped 82 Degree Countersink with No Burning and Marring Adjustable Fr... Carbide-Tipped 82 Degree Countersink with No Burning and Marring Adjustable Free Spinning Low Friction Depth-Stop with No-Thrust Ball Bearing more
-
-
Amana Tool 47100 Flush Trim wi...Amana Tool 47100 Flush Trim with Ball Bearing Guide 3/8-Inch Diameter by 1-Inc... Amana Tool 47100 Flush Trim with Ball Bearing Guide 3/8-Inch Diameter by 1-Inch Cutting Height by 1/4-Inch Shank Carbide Tipped Router Bit Excellent for Template Work 3/8-Inch Cutting Diameter 1-Inch Cutting Height 2-5/8-Inch Length 1/4-Inch Shank 2... more
-
Amana Tool 45481 Flush Trim/Pa...Amana Tool 45481 Flush Trim/Pattern Plunge 1/2-Inch Diameter by 3/8-Inch Cutti... Amana Tool 45481 Flush Trim/Pattern Plunge 1/2-Inch Diameter by 3/8-Inch Cutting Height by 1/4-Inch Shank Carbide Tipped Router Bit 1/2-inch cutting diameter 3/8-inch cutting height 2-1/4-inch length 1/4-inch shank 2 flute Carbide tipped industrial... more
-
Amana Tool 49504 Carbide Tippe...2 Flute and 4 Flute The router bits found on this page include the miniature 3... 2 Flute and 4 Flute The router bits found on this page include the miniature 3/16 and 1/4 diameter ball bearings for routing tight spaces the In-Tech insert replacement knife series diamond tipped (PCD) bits as well as the standard 1/2 diameter ball... more
-
Amana Tool - 47102 Carbide Tip...Amana Tool - 47102 Carbide Tipped Flush Trim 3/8 Dia x 1/2 x 1/4 Shank Amana Tool - 47102 Carbide Tipped Flush Trim 3/8 Dia x 1/2 x 1/4 Shank more
-
Amana Tool - 57220 Carbide Tip...Chamfer and even bevel solid-surface edges with one of these two bits. These l... Chamfer and even bevel solid-surface edges with one of these two bits. These large bits must be run at reduced speed in a high-horsepower router #57220 diameter (D): 2 angle (a°): 45° cutting Height (B): 3/4 shank (D): 1/2 overall length (L): 2-5/8... more
-
Amana Tool 45477 Carbide Tippe...Use a Two-Flute bit where fine finish is paramount. Two flutes balance the bit... Use a Two-Flute bit where fine finish is paramount. Two flutes balance the bit eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface but feed rate is slightly reduced. Excellent for cutting #45477 diameter... more
-
Amana Tool - (49706) Carbide T...This bit creates a flat-bottom Groove between two quarter-round shapes. Short ... This bit creates a flat-bottom Groove between two quarter-round shapes. Short vertical walls extending below the radius lend extra depth to the appearance. Depending upon the cut depth adjustment The radii can be flush with the work surface or... more
-
Amana Tool - 49493 - 49492 Car...Amana Tool - 49493 - 49492 Carbide Tipped Corner Round 1/16 Radius x 5/8 Dia x... Amana Tool - 49493 - 49492 Carbide Tipped Corner Round 1/16 Radius x 5/8 Dia x 5/16 x 1/4 Sha Visit the Store Visit the Store Visit the Store Visit the Store Visit the Store Amana Tool is an industry leader for over 50 years specializing in industrial... more
-
Amana Tool MB10800 Carbide Tip...Specifically designed to cut melamine chip-free on both sides provided that yo... Specifically designed to cut melamine chip-free on both sides provided that your table saw fence is square to the blade and the arbor is running true.Special High-ATB grind (with 25 degree bevels) slices cleanly through fragile surface coatings like... more
-
Amana Tool 47105 Dynabit Lamin...The dynamic line features a modest down-shear for an excellent finish. The hel... The dynamic line features a modest down-shear for an excellent finish. The helix bits have a spiral-like twist to the cutting edges making them especially good on difficult materials such as melamine. An adhesive-trapping gap between cutting edges and... more
-
Amana Tool 45475-S Carbide Tip...Decorate your home with these beautiful Fall Lead Photo/Balloon Holders! Perfe... Decorate your home with these beautiful Fall Lead Photo/Balloon Holders! Perfect for Thanksgiving! Size: 6 Ozs. You get 6 each for this price.. Enjoy our Beistle Fall Leaf Photo/Balloon Holder (Case of 6) at a discount price and quick shipping. more
-
Amana Tool 45707 Carbide Tippe...Industrial Quality Signmaking Lettering V Groove Miter Fold are made by Amana ... Industrial Quality Signmaking Lettering V Groove Miter Fold are made by Amana Tool the leading manufacturers of high-quality wood-cutting tools. Cut decorative V grooves and lettering on signs with Amana Tool 45707 Carbide Tipped Zero Point V Groove 60... more
-
amana tool - sc404 carbide tip...rub collar for 3/4 arbor only! #sc404 (d) diameter: 4-15/16 (d) bore: 1/2 & 3/... rub collar for 3/4 arbor only! #sc404 (d) diameter: 4-15/16 (d) bore: 1/2 & 3/4 (a) angle: 17 (b) cutting height: 5/8 c: 1/4 optional rub collar: c-004 sc404 carbide tipped 3-wing traditional raised panel 17 deg x 4-15/16 dia x 5/8 x 1/2 & 3/4 bore for... more
-
Amana Tool 45526 Carbide Tippe...Surfacing Planing Router Bits are made by Amana Tool the leading manufacturers... Surfacing Planing Router Bits are made by Amana Tool the leading manufacturers of high quality wood cutting tools. If you are looking for the ultimate in tooling use Amana Tool DRB-440 Polycrystalline Diamond (PCD) Tipped 1-1/2 Dia x 1/2 Cut Height x... more
-
Amana Tool - 49112 Carbide Tip...The covetto form – produced by the cove Bit – is one of the classic buildi... The covetto form – produced by the cove Bit – is one of the classic building blocks for many molding profiles. Use it alone or in combination with Beads and fillets. Use the cove to detail The edges of casework doors and drawers Posts and columns.... more
-
Amana Tool - 55239 Carbide Tip...Amana Tool - 55239 Carbide Tipped Adjustable Countersink with Depth-Stop 3/8 D... Amana Tool - 55239 Carbide Tipped Adjustable Countersink with Depth-Stop 3/8 Dia x 49 Degr A new addition to the well known range of Amana Tool countersinks. Unique adjustable depth-stop developed for Quick and easy adjustment of the countersink... more
-
Amana Tool - 45436 Carbide Tip...Use a Two-Flute bit where fine finish is paramount. Two flutes balance the bit... Use a Two-Flute bit where fine finish is paramount. Two flutes balance the bit eliminating vibration that degrades the cut finish. Two cuts per revolution yield a smooth surface but feed rate is slightly reduced #45436 diameter (D): 11/16 cutting... more
-
Amana Tool 1-1/4 Diam 3/4 LOC ...Amana Tool 1-1/4 Diam 3/4 LOC 2 Flute Carbide-Tipped Edge Profile Mortising Ro... Amana Tool 1-1/4 Diam 3/4 LOC 2 Flute Carbide-Tipped Edge Profile Mortising Router Bit 1/2 Shank Diam 2-1/8 OAL Use on Wood more
-
Amana Tool 45468 Carbide Tippe...This bit is essentially a plunge-cutting straight with a shank-mounted ball-be... This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile useful for template/pattern routing of parts joints internal cuts and can be used in handheld and table-mounted routers. The template is attached to... more
-
Amana Tool 56144 Carbide Tippe...Industrial Quality Signmaking Lettering V Groove Miter Fold & Mini Router Bits... Industrial Quality Signmaking Lettering V Groove Miter Fold & Mini Router Bits are made by Amana Tool the leading manufacturers of high-quality wood-cutting tools. Use Amana Tool 56123 Carbide Tipped Point Cutting Roundover 1/4 R x 1/2 D x 1/2 CH x 1/4... more
-
Amana Tool 45527 Carbide Tippe...Surfacing Planing Router Bits are made by Amana Tool the leading manufacturers... Surfacing Planing Router Bits are made by Amana Tool the leading manufacturers of high quality wood cutting tools. If you are looking for the ultimate in tooling use Amana Tool DRB-440 Polycrystalline Diamond (PCD) Tipped 1-1/2 Dia x 1/2 Cut Height x... more
-
Amana Tool - SC502 Carbide Tip...Rub collar for 1-1/4 Arbor only! #SC502 (D) diameter: 5-1/2 (D) bore: 1 & 1-1/... Rub collar for 1-1/4 Arbor only! #SC502 (D) diameter: 5-1/2 (D) bore: 1 & 1-1/4 (B) Cutting height: 5/8 (r) radius: 1-15/32 C: 5/16 R1: 1/8 optional rub collar: c-017 R2: 7/8 SC502 carbide Tipped 3-Wing Ogee raised panel 5-1/2 dia x 5/8 x 1 & 1-1/4... more
-
Amana Tool 45487 Flush Trim Te...This bit is essentially a plunge-cutting straight with a shank-mounted ball-be... This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. It is a versatile bit useful for template/pattern routing of parts joints and internal cuts and can be used in handheld and table-mounted routers. The template... more
-
Amana Tool 55223 Carbide Tippe...Carbide tipped industrial plug cutters. Readreview of carbide tipped plug cutt... Carbide tipped industrial plug cutters. Readreview of carbide tipped plug cutters. Note: Must clamp work piece firmly to drill press table. more
-
Amana Tool SC577 Carbide Tippe...Also known as stile and post shaper cutters. Carbide Tipped Tongue & Groove Mi... Also known as stile and post shaper cutters. Carbide Tipped Tongue & Groove Mission Style and Arts & Crafts Reversible Stile and Rail Shaper Cutters for 3/4 Material Designed for template shaping such as arched or cathedral doors etc. Features a ball... more
-
Amana Tool MB10800C Electro-Bl...Specifically designed to cut melamine chip-free on both sides provided that yo... Specifically designed to cut melamine chip-free on both sides provided that your table saw fence is square to the blade and the arbor is running true.Special High-ATB grind (with 25 degree bevels) slices cleanly through fragile surface coatings like... more
-
Amana Tool - 45418 Carbide Tip...Use a Two-Flute bit where fine finish is paramount. Two flutes balance the bit... Use a Two-Flute bit where fine finish is paramount. Two flutes balance the bit eliminating vibration that degrades the cut finish. Two cuts per revolution Yield a smooth surface but feed rate is slightly reduced #45418 diameter (D): 1/2 cutting height... more
-
Amana Tool 54314 3-Piece Carbi...Amana Tool 54314 3-Piece Carbide Tipped Tambour Door / Appliance Garage Door 1... Amana Tool 54314 3-Piece Carbide Tipped Tambour Door / Appliance Garage Door 1/2 Inch SHK Router Bit Set Unique 3-piece router bit set with antique solid brass knob Shapes tambours that interlock with a ball-and-socket joint Unlike ordinary tambours... more
-
Amana Tool 45525 Carbide Tippe...Surfacing Planing Router Bits are made by Amana Tool the leading manufacturers... Surfacing Planing Router Bits are made by Amana Tool the leading manufacturers of high quality wood cutting tools. 1-1/2 Dia x 1/2 Cut Height x 1/2 Shank x 2-1/2 Inch Long Spoilboard CNC Router Bit. Excellent for: Aluminum Bronze & Copper Aluminum... more
-
Amana Tool - (45924) Carbide T...Cut half-round grooves for Fluted moldings columns millwork and signs using a ... Cut half-round grooves for Fluted moldings columns millwork and signs using a core box bit. Used with an edge guide It can cut coves. Can be used with handheld table-mounted and CNC routers. Perfect for making flutes on CNC machines perfect for juice... more
-
amana tool - 45110 carbide tip...In choosing a straight bit for any application always select one with the shor... In choosing a straight bit for any application always select one with the shortest cutting edges and the shortest overall length that will reach the required CUT depth. Excessive length intensifies deflection and vibration which degrade cut quality and... more
-
Amana Tool 45364 Carbide Tippe...Trimming Router Bits are made by Amana Tool the leading manufacturers of high ... Trimming Router Bits are made by Amana Tool the leading manufacturers of high quality wood cutting tools. Amana Tool 45364 Carbide Tipped Down Shear Face Plunge Template 3/4 D x 2 Inch CH x 1/2 SHK w/ Upper Ball Bearing Router Bit is useful for... more
-
Amana Tool 45427-01 Carbide Ti...In choosing a straight bit for any application always select one with the shor... In choosing a straight bit for any application always select one with the shortest cutting edges and the shortest overall length that will reach the required cut depth. Excessive length intensifies deflection and vibration which degrade cut quality and... more
-
Amana Tool - (45467) Carbide T...This bit is essentially a plunge-cutting straight with a shank-mounted ball-be... This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile useful for template/pattern routing of parts joints internal cuts and can be used in handheld and table-mounted routers. The template is attached to... more
-
Amana Tool - (45452) Carbide T...Use a Two-Flute bit where fine finish is paramount. Two flutes balance the bit... Use a Two-Flute bit where fine finish is paramount. Two flutes balance the bit eliminating vibration that degrades the cut finish. Two cuts per revolution Yield a smooth surface but feed rate is slightly reduced #45452 diameter (D) 1-1/2 cutting height... more
-
Amana Tool - 45464 Carbide Tip...This bit is essentially a plunge-cutting straight with a shank-mounted ball-be... This bit is essentially a plunge-cutting straight with a shank-mounted ball-bearing pilot. Versatile useful for template/pattern routing of parts joints internal cuts and can be used in handheld and table-mounted routers. The template is attached to... more
-
Amana Tool - LB86401C Electro-...When cutting acrylics and plastics chip-welding – A melting of the material ... When cutting acrylics and plastics chip-welding – A melting of the material is a concern. But not with these non-melt blades. With a modified triple-chip grind and a 2° negative hook angle They produce less heat than a standard blade leaving a crisp... more
-
Amana Tool - (55293) Carbide T...These tools combine carbide Countersink high-speed-steel drill bit and free-sp... These tools combine carbide Countersink high-speed-steel drill bit and free-spinning low friction depth-stop. The countersink leaves a clean hole edge and the adjustable depth-stop doesn t mar the surface. The large openings around the collar allow the... more
-
Amana Tool 49506 Carbide Tippe...2 Flute and 4 Flute The router bits found on this page include the miniature 3... 2 Flute and 4 Flute The router bits found on this page include the miniature 3/16 and 1/4 diameter ball bearings for routing tight spaces the In-Tech insert replacement knife series diamond tipped (PCD) bits as well as the standard 1/2 diameter ball... more
Ads related to amana tool 45442 carbide tipped
Shopping for the best deal on Amana tool 45442 carbide tipped Power Tools - Select a product below or see other matches to read product reviews, compare prices and store ratings.